THE OLSSON RUBY

COMPATIBILITY

Image

THE OLSSON RUBY &
OLSSON RUBY MK8

ABRASIVE MATERIALS AT NORMAL
SPEEDS & TEMPERATURES

Excellent performance, wear-resistance and reliability.

Available in two lengths, compatible with a wide range of printers.
DETAILS, SPECS & COMPATIBILITY
Image

THE OLSSON RUBY &
HIGH OUTPUT (HO)

ABRASIVE MATERIALS AT  HIGH SPEEDS

A longer melt zone provides even higher throughput / speed, reducing the time needed to print large objects, while maintaining excellent wear-resistance and reliability.

DETAILS, SPECS & COMPATIBILITY
Image

 THE OLSSON RUBY
HIGH TEMP (HT)

ABRASIVE MATERIALS AT HIGH TEMPS 300ËšC +

A high-performance copper alloy with a non-stick surface coating enables a maximum operating temperature of 500 ° C, while maintaining excellent wear-resistance and reliability.

DETAILS, SPECS & COMPATIBILITY
AT A GLANCE

COMPARISON

CLASSIC

HIGH
TEMP.

MK8

HIGH
OUTPUT

Filament Diameter

1.75mm

✓

✓

✓

✓

2.85mm

✓

✓

Nozzle Diameter

0.4mm

✓

✓

✓

✓

0.6mm

✓

✓

✓

✓

0.8mm

✓

✓

✓

✓

Max. Operating Temp.

300ËšC

500ËšC

300ËšC

300ËšC

Ruby Abrasion Resistance

✓

✓

✓

✓

Thread Length

7mm

7mm

5.5mm

15.5mm

THE OLSSON RUBY

CLASSIC

Excellent performance, wear-resistance and reliability, in a "V6" style nozzle.

NOZZLE DIAMETERS

Image

FILAMENT DIAMETERS

Image

THREAD LENGTH

Image

COMPATIBLE HOTENDS  1.75mm

E3D BigBox

All E3D V4 / V5 / V6 1.75mm hotends
(& clones) including:

Prusa MK2 / MK2S / MK3 / Mini
Lower the heatsink and heatbreak half a turn while the block is hot to ensure a proper seal.

Felix Pro 2. Several testers reports success.
Ruby is longer than stock nozzle so Z height needs to be adjusted. Ensure you keep track of the orientation of the heater block during installation.

gCreate gMax 1.5XT +

Robo3D R2

Raise3D N1 / N2 / N2+ with V2 hotend
Make sure to re-adjust your z-stop when using the Ruby nozzle as it does not match the height of the standard nozzle. Depending on the age of your printer, clearance may be an issue. Updates to the cooling fan ducts mean that there may not be enough room left for the Olsson Ruby. NOT compatible with the Raise3D Pro2 series due to a change in the heat break geometry.

COMPATIBLE HOTENDS 2.85mm

All E3D V4 / V5 / V6 3.0mm hotends 
You will need to mount it with the nozzle not placed against the front face of the heater block but against the heat break / insulator tube to create a seal.

Ultimaker 2 + / 2+ Extended ,
Ultimaker 2/2
Extended with Olsson block upgrade
Ultimaker Original, Original + 
You will need to adjust the fan shroud since the nozzle is shorter than the original nozzle. You will need to mount it with the nozzle not placed against the front face of the heater block but against the heat break / insulator tube to create a seal.

Lulzbot TAZ 3/4 with hexagon hotend upgrade
You will need to mount it with the nozzle not placed against the front face of the heater block but against the heat break / insulator tube to create a seal.
Lulzbot TAZ 5
Lulzbot TAZ 6
You will need to mount it with the nozzle not placed against the front face of the heater block but against the heat break / insulator tube to create a seal. Will require disabling of the automatic bed leveling since the ruby ​​tip is not conductive.

3ntr A2 v2 /  A4 v3

Please note that no Micro-Swiss style hot-ends are compatible with The Olsson Ruby and will damage your nozzle.

THE OLSSON RUBY

MK8

Excellent performance, wear-resistance and reliability, in an "MK8" style nozzle.

NOZZLE DIAMETERS

Image

FILAMENT DIAMETERS

Image

THREAD LENGTH

Image

COMPATIBLE HOTENDS

Creality CR-10
(NOT the CR-10S Pro)
Creality Ender 2/3

CraftBot + / XL series

Makerbot Replicator 2 / 2X / Smart Extruder

SeeMeeCNC Artemis * 4
Several testers reports success. Ruby is longer than stock nozzle so Z height needs to be adjusted.

SeeMeeCNC Rostock Max V3

Monoprice mini V1 /  V2

Please note that no Micro-Swiss style hot-ends are compatible with The Olsson Ruby and will damage your nozzle.

THE OLSSON RUBY

HIGH OUTPUT (HO)

A longer melt zone provides even higher throughput / speed, reducing the time needed to print large objects, while retaining excellent wear-resistance and reliability.

NOZZLE DIAMETERS

Image

FILAMENT DIAMETERS

Image

THREAD LENGTH

Image

COMPATIBLE HOTENDS

E3D Volcano (1.75, 2.85 mm)

Lulzbot MOARstruder (2.85mm)

Please note that no Micro-Swiss style hot-ends are compatible with The Olsson Ruby and will damage your nozzle.

THE OLSSON RUBY

HIGH TEMPERATURE (HT)

A high-performance copper alloy with a non-stick surface coating enables a maximum operating temperature of
500°C, while maintaining excellent wear-resistance and reliability. Same thread as the Olsson Ruby Classic.

NOZZLE DIAMETERS

Image

FILAMENT DIAMETERS

Image

THREAD LENGTH

Image

COMPATIBLE HOTENDS  1.75mm

E3D BigBox

All E3D V4 / V5 / V6 1.75mm hotends
(& clones) including:

Prusa MK2 / MK2S / MK3 / Mini
Lower the heatsink and heatbreak half a turn while the block is hot to ensure a proper seal.

Felix Pro 2. Several testers reports success.
Ruby is longer than stock nozzle so Z height needs to be adjusted.

gCreate gMax 1.5XT +

Robo3D R2

Raise3D N1 / N2
Adjustment of z-stop required, also see notes on the revision of your Raise3D printer in the Instructions for use. NOT compatible with the Raise3D Pro2 series due to a change in the heat break geometry.

COMPATIBLE HOTENDS 2.85mm

All E3D V4 / V5 / V6 3.0mm hotends 
You will need to mount it with the nozzle not placed against the front face of the heater block but against the heat break / insulator tube to create a seal.

Ultimaker 2 + / 2+ Extended ,
Ultimaker 2/2
Extended with Olsson block upgrade
Ultimaker Original, Original + 
You will need to adjust the fan shroud since the nozzle is shorter than the original nozzle. You will need to mount it with the nozzle not placed against the front face of the heater block but against the heat break / insulator tube to create a seal.

Lulzbot TAZ 3/4 with hexagon hotend upgrade
You will need to mount it with the nozzle not placed against the front face of the heater block but against the heat break / insulator tube to create a seal.
Lulzbot TAZ 5
Lulzbot TAZ 6
You will need to mount it with the nozzle not placed against the front face of the heater block but against the heat break / insulator tube to create a seal. Will require disabling of the automatic bed leveling since the ruby ​​tip is not conductive.

3ntr A2 v2 /  A4 v3

Please note that no Micro-Swiss style hot-ends are compatible with The Olsson Ruby and will damage your nozzle.

THE OLSSON RUBY

THE FUTURE

We have several models/sizes of the Olsson Ruby planned for future, however doing test iterations with new ruby nozzle geometries is affected by quite long lead times due to the complex manufacturing process. It helps us to prioritize if you submit your interest in the model/size you are most interested in.

Smaller / Larger Sizes
Submit Interest

Other 3D Printers & Hot-Ends
Submit Interest

3D Printer manufacturer/ OEM opportunities
Submit Interest